Pyramid, Puig, Ermax Puig Ermax
English French Russian Italian Spanish German Portuguese
View Cart (0)

On a mobile phone or tablet? We know mobile internet bandwidth can be expensive.
Click here to view the mobile device version of this page.


We advise that customers use our new 'VENTURE SHIELD' paintwork protection in order to avoid stone chipping. This is especially important for those colour matched parts that sit low to the ground. We feel that 'VENTURE SHIELD' is the most cost-effective paintwork protection solution on the market, providing an almost invisible protective barrier once applied. Search product code 08023A for more info

Polypropylene Bonding Kit ( Glue )

Fits Years: ALL

Polypropylene Bonding Kit  ( Glue )
Polypropylene Bonding Kit  ( Glue ) Polypropylene Bonding Kit  ( Glue )
Mouse over / click thumbnails to enlarge

Approx : $9.23 USD
Approx : €7.48 EURO
Part Code:[ 08018 ]
Stock:[ 77 ]


Click here to view the fitting instructions for this product


PP Polypropylene

Stick that if you can !


Polypropylene components are widely used in all transport sectors. Due to its "low surface energy", difficulty is experienced in achieving a satisfactory bond - either to itself or to other commonly used plastics.

Our bonding kit has been developed specifically to address this problem. The P108 primer wipe and gel cyanoacrylate make a strong bond achievable, but it is important to please follow the instructions very carefully.

HOW DO I IDENTIFY POLYPROPYLENE ? : Look for the letters "PP" engraved on the reverse (B surface) of the moulding.

SAFETY : Cyanoacrylate adhesive, Super Glue, bonds skin in seconds. Handle with great care. Use the gloves provided and keep out of the reach of children.

PREPARATION : Always remove parts from the bike and carry out your task on a work bench. If fitting an accessory, first trial fit the product to ensure that you are happy with the arrangement. Protect adjacent decorative "A" surfaces from any excess adhesive with carefully applied masking tape. Ensure all components are clean and then key both surfaces with the 150 grit paper. The best possible face to face contact is vital and clamping may be required. Clamping as in fig 1 and fig 2 must be trialed before the adhesive is applied. To improve the stability of the clamps on the component faces, try placing foam rubber, masking tape or similar on the feet of the clamps.

ASSEMBLY : It is important to apply the adhesive in parallel "tram lines" as shown in fig 3 - do not apply in an enclosed circular pattern. This is a "single pack" adhesive which relies on contact with air to fully cure and give maximum bond strength.

When attaching any clamps, please pay particular attention to any corner details at the extreme edges as these are the places most prone to subsequent bond failure. When applying adhesive and assembling, it is important to pay attention to the orientation of the parts so that any run-off of the adhesive is away from the decorative "A" surfaces. Bonding will take place quickly. However, once applied, the clamps should be left in place for one hour.

Finally, and this is very important, please resist the temptation to "test" the bond strength. This may weaken or break the bond completely.

Current rating: 10 / 10

There are currently no reviews of this accessory!

Click here to write a review

Please note that unless otherwise stated all accessories have been designed to fit the standard bike.

Please contact our sales team on 01427 677990 or email us at if you require any further information or assistance.

Images used on our website may be for illustration purposes only. Please note that colour matched products may be affected by lighting in certain images (Indoor or Outdoor, etc.)

Click below to translate this page to your prefered language

Francais      Deutsch      Espanol      Italiano      Pусский      中文

© Copyright Pyramid Plastics Ltd 2018 Sitemap
breadcrumb1 breadcrumb2 breadcrumb3 breadcrumb4 breadcrumb5 breadcrumb6 breadcrumb7 breadcrumb1_stretched