Pyramid, Puig, Ermax Puig Ermax
English French Russian Italian Spanish German Portuguese
View Cart (0)

On a mobile phone or tablet? We know mobile internet bandwidth can be expensive.
Click here to view the mobile device version of this page.


We advise that customers use our new 'VENTURE SHIELD' paintwork protection in order to avoid stone chipping. This is especially important for those colour matched parts that sit low to the ground. We feel that 'VENTURE SHIELD' is the most cost-effective paintwork protection solution on the market, providing an almost invisible protective barrier once applied. Search product code 08023A for more info

BMW R1200RS 2015 > External Glue Fit Extenda Fenda

Fits Years: 2015 ≥

BMW R1200RS 2015 > External Glue Fit Extenda Fenda
BMW R1200RS 2015 > External Glue Fit Extenda Fenda BMW R1200RS 2015 > External Glue Fit Extenda Fenda BMW R1200RS 2015 > External Glue Fit Extenda Fenda
Mouse over / click thumbnails to enlarge

Approx : $36.06 USD
Approx : €31.86 EURO
Part Code:[ 054241 ]
Stock:[ 32 ]


Click here to view the fitting instructions for this product


Designed to protect your bike from debris thrown up by the front tyre.

The Extenda Fenda helps keep rider and bike cleaner, cuts down on paint damage on the lower fairing and also protects important parts of the bike such as the radiator and oil cooler.


Extenda Fenda (ABS black plastic)
Pyramid No Screws Glue
Alcohol Wipe

Remove front mudguard (fender) from motorcycle before fitting this Pyramid product.

Clean both the inside and outside of the mudguard with warm soapy water and dry with towel or cloth. Once dry, use the sandpaper provided and key (rub) the outside surface of your mudguard and the inside surface of the Extenda.

Offer the Extenda up to the mudguard and ensure you know exactly where you intend to position the Extenda before applying the Pyramid No Screws Glue. As highlighted on our fitting instruction sheet, the indents on the rear of the mudguard must match up and sit at the bottom of the guard.

Place the glue in diagonal lines along the guard from left to right leaving 10-15mm in between each bead and make sure you leave a 10-15mm gap at the top edge of the Extenda so the glue does not squeeze out. (If it does, please wait for it to cure before removing it).

Carefully place the Extenda onto the guard, making sure you align it as before and clamp it in place for at least 24 hours.

IMPORTANT : Please do not be tempted to check if the glue on the Extenda has cured before the minimum 24 hour period. This may cause the adhesive bond to fail and it could leave you with a mess!


NEW!! Frame End Caps for R1200R/RS 2015+

R1200RS Huggers

R1200RS Front Mudguard

R1200RS Ductail

R1200RS Belly Pan

R1200RS Screen Range

R1200RS Headlight Cover Range

Current rating: 10 / 10

There are currently no reviews of this accessory!

Click here to write a review

Please note that unless otherwise stated all accessories have been designed to fit the standard bike.

Please contact our sales team on 01427 677990 or email us at if you require any further information or assistance.

Images used on our website may be for illustration purposes only. Please note that colour matched products may be affected by lighting in certain images (Indoor or Outdoor, etc.)

Click below to translate this page to your prefered language

Francais      Deutsch      Espanol      Italiano      Pусский      中文

© Copyright Pyramid Plastics Ltd 2018 Sitemap
breadcrumb1 breadcrumb2 breadcrumb3 breadcrumb4 breadcrumb5 breadcrumb6 breadcrumb7 breadcrumb1_stretched